利用调度优化模型研究原油调合方案的可行性

针对某沿海炼油企业拟投用原油调合系统以稳定混炼原油的性质,设计方案要求将部分码头罐的操作模式由混储改为单储的情况,采用约束规划与数学规划复合建模,实现了码头至厂区大容积长输线模拟,建立了该企业的原油调度优化模型并研究了设计方案的可行性。针对240h调度周期、10种可加工原油、3艘到港油轮的复杂工况进行了优化计算。结果表明:该设计方案具备可行性,且油轮仍可实现到港即卸油,蒸馏装置混炼油种也可长时间保持稳定;模型的优化计算时间较短(小于15min),且对长输线收付及存油情况模拟准确,复合建模方法满足工业应用要求。     

Optimal design of Raman fibre amplifier based on terminal value optimization strategy and shuffled frog leaping algorithm

This paper introduces an evolutionary algorithm, Shuffled Frog Leaping Algorithm (SFLA), to solve the optimization problem in designing the multi-pumped Raman Fibre Amplifier (RFA). SFLA is a powerful optimizer tool because of its efficient mathematical expressions and global search capability. We utilize SFLA to determine the optimal pump wavelengths and pump powers by minimizing the gain ripple of RFA. To accelerate calculations, a terminal value optimization strategy (TVOS) is incorporated into the evolution of SFLA. This proposed strategy takes the terminal power values of pumps as the decision variables in optimization. Then, the optimal original power values of the pumps are obtained by solving the Power Coupled Equations once, without using the traditional method of repetitive guesses.The combination of SFLA and TVOS enhances the efficiency of optimization and accelerates calculation, while satisfying the design requirements of RFA.The simulation results show that nearly 65% of computational time has been saved compared with the traditional average power analysis. The 4-pumped C+L band of backward multi-pumped RFA with the average net gain of 0 dB, 1 dB and 2 dB are designed individually, where the gain ripple is less than 0.64 dB. The combination of SFLA and TVOS enhance the optimization efficiency and improve the performance of RFA with good gain profile.     

攀西钒钛磁铁矿尾矿制备储水泡沫陶瓷的研究

以攀西钒钛磁铁尾矿和废玻璃为主要原料通过高温烧结法制备储水泡沫陶瓷，研究原料配比和发泡剂（SiC）添加量对材料性能的影响。结果表明:随着钒钛磁铁矿尾矿含量的增加，材料的体积密度及抗压强度逐渐增大，平均气孔孔径逐渐减小；当尾矿添加量为50 wt%，材料的体积吸水率出现极值。当SiC添加量为0.3 wt%，材料内部气孔分布均匀，平均孔径约为2.93 mm。最终以50.0 wt%的钒钛磁铁矿尾矿和50.0 wt%的废玻璃为原料，外加3.0 wt%的石英，0.3 wt%的SiC，3.0 wt%的Na3PO4，在1040℃下制得性能最优的储水泡沫陶瓷，材料的体积密度为0.26 g/cm-3、体积吸水率为56.5%和抗压强度为0.68 MPa。采用SEM、XRD等检测手段研究材料的微观形貌及物相组成，结果表明储水泡沫陶瓷内部由三维立体结构组成，有利于储存水分；材料主要物相包括硅灰石、长石、透辉石和钛铁矿。      

In Silico Study on Tumor-Size-Dependent Thermal Profiles inside an Anthropomorphic Female Breast Phantom Subjected to Multi-Dipole Antenna Array

Electromagnetic hyperthermia as a potent adjuvant for conventional cancer therapies can be considered valuable in modern oncology, as its task is to thermally destroy cancer cells exposed to high-frequency electromagnetic fields. Hyperthermia treatment planning based on computer in silico simulations has the potential to improve the localized heating of breast tissues through the use of the phased-array dipole applicators. Herein, we intended to improve our understanding of temperature estimation in an anatomically accurate female breast phantom embedded with a tumor, particularly when it is exposed to an eight-element dipole antenna matrix surrounding the breast tissues. The Maxwell equations coupled with the modified Pennes’ bioheat equation was solved in the modelled breast tissues using the finite-difference time-domain (FDTD) engine. The microwave (MW) applicators around the object were modelled with shortened half-wavelength dipole antennas operating at the same 1 GHz frequency, but with different input power and phases for the dipole sources. The total input power of an eight-dipole antenna matrix was set at 8 W so that the temperature in the breast tumor did not exceed 42 °C. Finding the optimal setting for each dipole antenna from the matrix was our primary objective. Such a procedure should form the basis of any successful hyperthermia treatment planning. We applied the algorithm of multi for multi-objective optimization for the power and phases for the dipole sources in terms of maximizing the specific absorption rate (SAR) parameter inside the breast tumor while minimizing this parameter in the healthy tissues. Electro-thermal simulations were performed for tumors of different radii to confirm the reliable operation of the given optimization procedure. In the next step, thermal profiles for tumors of various sizes were calculated for the optimal parameters of dipole sources. The computed results showed that larger tumors heated better than smaller tumors; however, the procedure worked well regardless of the tumor size. This verifies the effectiveness of the applied optimization method, regardless of the various stages of breast tumor development.     

基于背压和最佳阀位控制的滑压曲线实时优化及应用

针对目前凝汽器背压对滑压值的修正无普适算式可供遵循的问题，通过作图法推理获得了滑压设定值与凝汽器背压及机组负荷之间的二元函数表达式；利用流量变工况计算方法解决最佳综合阀位的确定问题，在满足机组日常运行需求的条件下达到汽轮机高压调阀节流损失最小化；将提出的基于凝汽器背压和机组负荷的二元函数滑压实时优化和基于流量变工况计算的最佳综合阀位控制滑压实时优化方法相结合，将凝汽器背压对滑压值的修正作为粗调，将最佳综合阀位控制对滑压值的修正作为细调，共同实现对滑压设定值的实时调整。在某660 MW超临界机组上的应用表明，该方法能够节约供电煤耗约1.12 g/(kW·h）。     

Understanding the determinants on household electricity consumption in Korea: OLS regression and quantile regression

The paper aims to investigate the determinants of household electricity consumption in Korea by using both the OLS regression and quantile regression. The results show that the effects of socio-demographic, dwelling, and electricity consumption characteristics on household electricity consumption may differ between two regressions and may differ across quantiles. We found that age group of household head, number of household, housing area, the number of household appliances, and refrigerator usage time were significant in all quantiles.     

计及风险规避的电力零售商平衡市场交易模型

由于新能源出力以及终端负荷需求的不确定性,电力零售商在日前市场的竞标电量与实时市场的购买电量之间存在不平衡而产生惩罚成本风险。引入用户侧可控负荷作为平衡资源参与市场交易,提出了一种风险规避程度指标,以此来度量交易前后电量偏差程度,以信息熵度量残差序列离散程度计算风险规避程度指标。以电力零售商运行收益、用户需求响应满意度以及风险规避程度最大为目标建立多目标风险规避模型,采用自适应权重粒子群算法进行模型求解。通过算例表明,所提出的模型从电网-电力零售商-用户多个角度去考虑电力零售商参与平衡市场交易策略,能够有效提高电力零售商的运行效益以及用户满意度,同时可以提高电力市场管理的可靠性与安全性。     

直投式纳豆菌发酵剂制备工艺优化

为探索出一种工艺简便、成本低且活菌数高的直投式纳豆菌（Bacillus natto）发酵剂的制备方法，该研究以大米粉为基质替代传统的种子液培养基培养纳豆菌后直接将其烘干制成直投式纳豆菌发酵剂，通过单因素及正交试验优化直投式纳豆菌发酵剂的制备工艺。结果表明，用含1.5%蛋白胨的大米粉作为培养基，在接种量4.0%、加水量40%、培养温度43 ℃条件下培养纳豆菌28 h，菌体生长良好，将培养物烘干后制成的直投式纳豆菌发酵剂中的活菌数含量达4.71×109 CFU/g。此技术操作简便，可推广至工业生产中，简化生产过程。